6 mm tempered glass
1 / 8
Clear glass panel 60 × 120 cm
Clear 6 mm tempered float glass with four ground mounting holes. Wall plugs with screws and cover caps included, all you need is a drill. A ready-made, standard size to protect the wall behind a gas or induction hob, by the sink and between units.
We pack panels in wooden frames, and the crate walls are made of HDF board. The shipment is insured and marked for the courier as glass. Check it with the courier, and if it is damaged, draw up a damage report with them.
- 6 mm tempered glass
- 4 × Ø 8 mm holes, centre 50 mm from the edge
- 10,8 kg panel weight
- 14 days to return
Added to cart. Go to cart →
- Trapezoidal ground, polished edges
The pane edges have a trapezoidal grind and are polished: a bevelled, glossy chamfer runs around the whole panel. It refracts light beautifully and gives the glass an elegant, refined look. The holes are deburred and ground, so the screw head and cover cap sit flush.
- Included: 4 expansion plugs 6 × 35 mm with screws and 4 cover caps
You drive the plugs with screws into the wall through the holes in the glass, and the cover caps hide the screw heads. You need a 6 mm masonry drill bit for the wall. The plugs are suitable for concrete and brick; for plasterboard or hollow block, choose plugs for that substrate.

- Return within 14 days (ready-made catalogue sizes, terms and conditions, section 5.3)
- Payment via Paynow (BLIK, card, instant bank transfer) or by standard bank transfer
What you get
- 6 mm tempered glassMany times stronger than ordinary glass.
- Behind gas and induction hobsDesigned for walls behind gas and induction hobs.
- Safe if damagedBreaks into small pieces with blunt edges.
- Trapezoidal grind, polished edgesThe bevelled, polished chamfer refracts light beautifully and adds elegance to the panel.
- 4 holes Ø 8 mmThe centre of each hole is 50 mm from the edge; holes are deburred and ground. Wall plugs, screws and cover caps included.
- Insured shipping in a crateWooden frames and HDF board walls, marked for the courier.
Product description
A clear panel protects the wall behind the hob, sink and worktop from grease, steam and splashes, while hiding nothing. The texture of the wall, the tiles, the brick or the paint stays visible, so the panel suits anywhere you want to keep the existing finish and just protect it (the photo alongside is from an installation).
Pay attention to glass thickness. When comparing panels from different sellers, check how many millimetres the glass is, because many do not state it, and cheaper offers are sometimes only 4 mm. Ours are 6 mm: stiffer, more impact-resistant and better able to bear the load at the mounting holes.
6 mm float glass is tempered. It is many times stronger mechanically than ordinary glass, and if damaged it breaks into small pieces with blunt edges. The smooth surface with no grout lines or pores does not absorb moisture and just needs wiping with a soft cloth and glass cleaner.
Wall mounting, edge at the worktop. We make the holes in the pane itself, with the centre 50 mm from the edge, so you drill the fixing in the wall above the worktop, without colliding with it, and the lower edge of the panel can sit right against the worktop. Panels without holes are fixed at the glass edge, which requires drilling below that edge and lifting the panel above the worktop. With ours there is no gap where grease and moisture could collect.
In the set you get four 6 × 35 mm expansion plugs with screws and four metal cover caps that hide the screw heads. A 6 mm masonry drill bit is enough for the wall, and the holes in the glass serve as a template: mark the centre of each with a pencil, take the panel off, drill and install.
Size 60 × 120 cm is a standard format from our catalogue, so the order does not require a design or visualisation approval, and you can return the product in accordance with the terms and conditions.
Specification
- Dimensions
- 1200 × 600 mm (60 × 120 cm)
- Thickness
- 6 mm (thicker than the common 4 mm)
- Glass type
- float, clear, tempered
- Edges
- trapezoidal grind, polished
- Holes
- 4 × Ø 8 mm (deburred, ground), the centre of each 50 mm from the edge
- Fixings
- 4 wall plugs 6 × 35 mm with screws, 4 metal cover caps
- Area
- 0,72 m²
- Weight
- ok. 10,8 kg
- Shipping
- 5 working days, insured crate, PLN 80
- Product code (SKU)
- GLASS_6MM_FLOAT_PANEL_OTWORY_ZESTAW-MOCOWAN 60X120
- EAN
- 5903878910707
Installation step by step
- Hold the panel against the wall and level it on the worktop. Through the holes in the glass, mark the centre of each of the four holes with a pencil.
- Take the panel off and drill the holes in the wall. For 6 mm plugs you need a 6 mm masonry drill bit (hammer drill for concrete and brick, SDS if needed), to a depth of at least 45 mm. Do not drill through the glass.
- Insert the plugs, position the panel and drive the screws through the holes in the glass. Tighten gently, without excessive force, so you do not press the glass against the wall.
- Snap the cover caps onto the screw heads.


How to measure the space
- Measure the width and height in several places and note the smallest result. Walls are rarely perfectly straight.
- Choose a size no larger than the measured space. A standard panel is not cut to size, so leave a margin for installation.
- Check the position of sockets and switches relative to the panel edges. If a standard panel does not fit or you need cut-outs, ask for a quote for a made-to-measure panel.
Frequently asked questions
Will the glass arrive in one piece?
We pack panels in wooden frames, and the crates have HDF board walls. The shipment is insured and marked as glass. Check it with the courier, and if it is damaged, draw up a damage report with them. You will find more packing photos in the FAQ.
Why does glass thickness matter?
Thicker glass is stiffer and more impact-resistant, and it carries load better around the holes. Our panels have 6 mm tempered glass, whereas in many offers the glass is 4 mm or the thickness is not stated, so when comparing offers always check this parameter.
Is the glass safe?
Yes. Tempered glass is many times stronger than ordinary glass, and when damaged it breaks into small, blunt pieces.
What drill bit should I use for the wall?
For 6 × 35 mm expansion plugs use a 6 mm masonry drill bit: a hammer drill for concrete and brick (SDS is best for hard concrete), and for plasterboard or hollow block use bits for that substrate and suitable plugs. Hole depth at least 45 mm. Drill after taking the panel off, never through the glass.
Can the lower edge of the panel sit against the worktop?
Yes. The holes are in the pane itself, with the centre 50 mm from the edge, so you drill the fixing in the wall above the worktop, without colliding with it, and the panel does not need to be lifted above the worktop.
Can the panel be returned?
Yes. You can return clear panels in fixed catalogue sizes within 14 days, in accordance with section 5.3 of the terms and conditions. We handle complaints about defects within 14 working days.
Is the panel suitable for the wall behind a gas or induction hob?
Yes. A clear tempered glass panel is suitable for walls behind gas and induction hobs. Keep the clearances recommended by the hob and extractor manufacturer.
What is the difference between the version with fixings and the version without?
The glass is the same: 6 mm, tempered, four Ø 8 mm holes. The version with fixings includes 4 expansion plugs with screws and 4 cover caps. The version without fixings is PLN 155 cheaper and is for those who have their own fasteners.
Can I order a different size?
The other catalogue sizes are alongside. We quote clear panels in other dimensions individually: write to biuro@artinspiro.pl or call +48 796 333 876.